- 您现在的位置：买卖IC网 > Sheet目录310 > AP3156FVG-7 (Diodes Inc)IC LED DRIVER WHITE BCKLGT 16QFN
AP3156
HIGH EFFICIENCY 1X/1.5X/2X CHARGE PUMP
FOR WHITE LED APPLICATIONS
Serial Digital Interface
SDI Command Timing Protocol
For the SDI command to be successfully received by the AP3156, all SDI timing specifications must be satisfied.
When no command is being sent, the SDI pin should be held High. If the SDI pin goes Low and stays Low for a time length between
T SLO (min) and T SLO (max) and then goes High and stays High for the length between T SHI (min) and T SHI (max), one falling edge is
registered by the AP3156. The total number of falling edges registered before the SDI pin is held High for longer than the maximum
separation time T SEP(max) identifies the command that has been received by the AP3156. The next series of falling edges before
another separation time of T SEP represents the next command. In other words, the AP3156 counts the number of consecutive falling
edges on the SDI pin and a different number represents a different command.
Each command is executed after it is successfully received. If at any time the SDI pin is held Low for longer than the maximum chip
disable time T OFF(max) , then the AP3156 will be turned off and enters the shutdown mode. Setting the SDI pin switching from Low to High
will re-enable the AP3156 and leave the shutdown mode. If the SDI pin is held on for a time duration over T SEP , then an end of a
sequence (EOS) occurs with a number of pulse conformed to specified timing.
A valid dual-sequence command occurs when one valid sequence is defined as an instruction, and the other is defined as data. Both
sequences have number of pulses less than 33. Also, a valid single-sequence command occurs when the sequence has number of
pulses greater than 32.
First Sequence
Second Sequence
T SHI
T SLO
T SEP
T SEP
SDI
1
2
8
9
10
1
2
Channel Selection
Current Setting
Channel D1
Channel D2
Channel D3
Channel D4
Channel D5
Channel D6
Channel 1 in
dimming control
Channel 2 in
dimming control
Channel 3 in
dimming control
Channel 4 in
dimming control
Channel 5 in
dimming control
Channel 6 in
dimming control
Set Channel 1 to current level 2.
Set Channel 2 to current level 2.
Set Channel 3 to current level 2.
Set Channel 4 to current level 2.
Set Channel 5 to current level 2.
Set Channel 6 to current level 2.
Figure 1: Dimming Control Selection (Dual-Sequence Command)
AP3156 Rev. 1
11 of 15
www.diodes.com
SEPTEMBER 2009
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AP5724WG-7
IC LED DRVR WHITE BCKLGT SOT26-6
AP5725FDCG-7
IC LED DRIVER WHITE BCKLGT 6-DFN
AP5726WG-7
IC LED DVR WHITE BCKLGT SOT26
AP8800AWT-7
IC LED DRIVER TSOT23-5
AP8800FNG-7
IC LED DRIVER HIGH BRIGHT 10DFN
AP8801M8G-13
IC LED DRIVER HIGH BRIGHT 8MSOP
AP8802HSP-13
IC LED DRIVER HIGH BRIGHT 8SOIC
AP8802SPG-13
IC LED DRIVER HIGH BRIGHT 8SOIC
相关代理商/技术参数
AP-316-G-A
制造商:Samtec Inc 功能描述:CONN DIP ADPTR PL 16 POS 2.54MM ST TH - Bulk
AP-316-G-A1
制造商:Samtec Inc 功能描述:CONN DIP ADPTR PL 16 POS 2.54MM ST TH - Bulk
AP-316-G-D
制造商:Samtec Inc 功能描述:CONN DIP ADPTR PL 16 POS 2.54MM ST TH - Bulk
AP-316-G-F
制造商:Samtec Inc 功能描述:CONN DIP ADPTR PL 16 POS 2.54MM ST TH - Bulk
AP-316-G-M
制造商:Samtec Inc 功能描述:CONN DIP ADPTR PL 16 POS 2.54MM ST TH - Bulk
AP-316-G-Q
制造商:Samtec Inc 功能描述:CONN DIP ADPTR PL 16 POS 2.54MM ST TH - Bulk
AP-316-T-A1
制造商:Samtec Inc 功能描述:CONN DIP ADPTR PL 16 POS 2.54MM ST TH - Bulk
AP-316-T-B
制造商:Samtec Inc 功能描述:CONN DIP ADPTR PL 16 POS 2.54MM ST TH - Bulk